ValueCut User Manual Blade Specification For cutting thick fluorescent and reflective vinyl. Also for cutting detailed work in standard vinyl. The blade is 45° with Red Cap(5-unit package), 0.25 mm offset For cutting reflective vinyl, cardboard, sandblast, flock, and stencil sharp edge. The blade is 60°.
There are a variety of circular saw blades. Each saw blade is designed to cut different materials and work with specific power saws. Be certain the blade is suitable for the material you need to cut and fits your saw. There are several specifications you need to consider.Compare the blade diameter and blade type with the capability of your saw.
Acceptable sizes vary by saw model, but the following generally applies:. Handheld circular saws accept smaller blades, those 4 1/2 inches to 7 1/4 inches in diameter. These are typically carbide-tipped. Tile saws use 7-inch or 10-inch diamond blades. Table saws and compound miter saws use blades 10 inches or 12 inches in diameter.
![Artcut Artcut](http://forum.uscutter.com/uploads/monthly_2017_09/X.png.baffbf68469475dbcd2e400e430f034e.png)
Like those for handheld saws, the blades are usually carbide-tipped. Metal-cutting chop saws, also called abrasive saws or cutoff saws, take 14-inch silicon carbide or aluminum oxide abrasive blades.Check the size of the arbor hole (the hole in the center of the blade). It must fit the arbor or shaft on your saw. Many blades with a circular arbor hole include a piece you can knock out to allow them to fit saws with a diamond-shaped arbor.Note the maximum RPM (revolutions per minute) rating of the blade to make sure it's compatible with the tool you plan to use.Learn how to choose the best power saw for your projects:.
![Artcut blade offset value calculator Artcut blade offset value calculator](http://forum.uscutter.com/uploads/monthly_2017_09/A.png.90a71b6fb3740d57894137a8fee72f30.png)
Standard circular saw blades are typically used to cut wood or wood composites. The number of teeth on the blade helps determine the speed, type and finish of the cut. Blades with fewer teeth cut faster, but those with more teeth create a finer finish. Gullets between the teeth remove chips from the work pieces. Expansion slots cut into the rim help prevent the blade from warping as it expands and contracts during use. They reduce vibration, creating a straighter cut.Rip-cut blades, for cutting with the woodgrain (along the length of a board), have fewer teeth (16 to 40).
The teeth are designed to cut aggressively, and deep gullets provide good chip removal. Crosscut blades, for cutting across the woodgrain (across the face of a board), have between 40 and 80 teeth designed for clean cuts.
Smaller gullets separate the teeth. Combination blades can make rip cuts and crosscuts. They have multiple groupings of teeth separated by deep gullets. Each group has one tooth for ripping and four for crosscutting.You may also see blades with other designations:. Framing blades have 24 teeth and are effective for work — such as rough carpentry — where speed is more important than a clean cut. Plywood blades have 100 or more fine teeth designed to create a finish with minimal splintering. Thin-kerf blades have a narrow profile for faster, easier cutting and less material waste.
Hollow-ground blades have a body that's thinner than the teeth — a design intended to help keep the blade from becoming pinched in the work piece.
Saintl.biz Software Solutions for Sign Making300 Posts108 TopicsLast post byinon Today at 10:47:27 AMsc-x2.com world leading software for signmaking9 Posts4 TopicsLast post byinon August 28, 2016, 11:08:18 PMwww.cadlink.com2 Posts2 TopicsLast post byinon March 18, 2011, 05:47:07 AMcorel.com Graphic design and illustration software17 Posts7 TopicsLast post byinon June 29, 2018, 02:40:00 AMadobe.com comprehensive vector graphics tools1 Posts1 TopicsLast post byinon May 07, 2009, 01:03:53 PMinkscape.org vector graphics editor6 Posts5 TopicsLast post byinon April 10, 2011, 12:10:33 AM.